If you’re looking for a woodworking vise with rock solid material holding performance, ease of installation and great features, consider this Quick-Release Front Vise by Veritas. U.S. Pat. screw and clamping capacity of 8-1/4" (less the thickness of your wooden jaws) Large front vise is 10-1/2" x 21" overall with a 1-1/8" dia. D673,830. Workbench build by René B., Kassel, Germany - with tail vise installation instructions. The aluminum chain cover consists of two cast end caps and a bridging extrusion, and must be cut to length for mounting at other than the maximum spacing.

2 Veritas® Quick-Release Front Vise Back Plate Half Nut Bushing Base Casting Main Screw* Jaw Mounting Screws Handle End Cap Quick-Release Shaft Half Nut Cam Guide Rod Quick-Release Spring Spring Nut Washer O-Ring Tee Quick-Release Lever Front Plate.

This is the bench in which the tailvise was installed. My bench top is 3" thick and the bench design needs the back chop of the vice to be flush with the table top. As a front vise, the Veritas twin-screw vise offers the strength of the conventional single-screw vise with the ability to hold a long board vertically.

We recommend that only experienced woodworkers try installing tailvise hardware. *Main screw cover (not shown) located under main screw.

screw and 13" clamping capacity (less the thickness of your wooden jaws) Larger vise has offset center screw to … Veritas® Quick-Release Front Vise: View Additional Info: Instruction Guide (816 KB, PDF) ... 20" wide by 5" tall, pad vise jaws; can be used with any front vise mechanism with guide rods 10" apart or less; installation instructions included: Product # Description 05G34.01: Veritas® Quick-Release Front Vise

… While these instructions are helpful, they cannot replace woodworking expertise. screw and clamping capacity of 8-1/4" (less the thickness of your wooden jaws) Large front vise is 10-1/2" x 21" overall with a 1-1/8" dia. Regular front vise is 7" x 14-3/4" overall with a 7/8" dia.


No. Figure 1: The Veritas® Quick-Release Front Vise mechanism, shown upside down.

Veritas Quick-Release Front Vise.

Front vise installation. 9,050,710 and U.S. Des. The downside is that it is physically quite wide, so unless your bench is pretty long, it may get in the way at times. Install in new bench (requires two hardwood jaws) or retrofit to existing one (requires end cap drilled for vise nuts and fixing bolts plus the vise jaw itself) Aluminum chain cover consisting of two cast end caps and bridging extrusion; cut to length for mounting at other than the maximum spacing Regular front vise is 7" x 14-3/4" overall with a 7/8" dia.

This means I cannot build and attach a full-sized rear chop as per the instructions. No. Pat. Veritas Twin-Screw Vice Installation Question 05-07-2013, 08:22 AM. Figure 1: The Veritas® Quick-Release Front Vise mechanism, shown upside down. The vise is an easy retrofit to an existing bench, requiring only the addition of two pieces: an end cap drilled for the vise nuts and fixing bolts, plus the vise jaw itself.

I'm now at the the stage of bench build where I'm getting ready to install a Veritas Twin-Screw Vice. Product # Description 05G12.26: Veritas® Twin-Screw Vise Accessories; 05G12.27: Optional Long Chain Cover* *For wider jaw capacity, the longer chain cover will accommodate vise screw centers up to 24". Because I sometimes have a friend, or my daughter, in the workshop working on something or helping me with something, I have installed a vise on the back slab of the workbench as well. Flip up a simple lever to disengage the Acme-threaded center screw to pull and push the vise freely and smoothly to accommodate your stock.